http://www.springfieldrecall.com/
 |
||
|
S&W Shield recall *****attention*****
|
IMPORTANT CONSUMER SAFETY ALERT and INSPECTION PROCEDURE – August 22, 2013 |
|
| PRODUCT: | ALL M&P Shield™ firearms manufactured before August 19, 2013. |
| DESCRIPTION OF THE HAZARD: | Smith & Wesson has identified a condition where the trigger bar pin could damage the lower trigger in certain M&P Shields in a way that may affect the functionality of the drop safety feature of the firearm, potentially allowing the pistol to discharge if it is dropped.Any unintended discharge of a firearm has the potential to cause injury, and we ask that you STOP USING YOUR PISTOL IMMEDIATELY UNTIL IT HAS BEEN INSPECTED AND, IF THE CONDITION IS FOUND, REPAIRED. |
| DESCRIPTION OF THE PRODUCT INVOLVED: | This Safety Alert applies to all M&P Shield pistols manufactured before August 19, 2013. We believe this condition is largely limited to recently manufactured M&P Shield pistols. However, out of an abundance of caution, we are asking all consumers of all M&P Shields manufactured before August 19, 2013 to immediately inspect their pistols for this condition. |
INSPECTING YOUR PISTOL:   |
Your firearm must be inspected to determine whether it exhibits the condition identified in this notice. To determine whether your firearm is affected by this condition, please inspect your firearm as follows (click here for video instructions):1. Follow the procedures in your Safety & Instruction Manual to ENSURE THE FIREARM IS UNLOADED; ENSURE THAT THE MUZZLE IS POINTED IN A SAFE DIRECTION; THE SLIDE IS LOCKED BACK; AND THE MANUAL SAFETY IS ENGAGED.2. Hold your pistol sideways with the muzzle pointed to the left. Look at the trigger. Note that the trigger is actually two pieces, with a pin in the middle that connects the two halves (Figure 1).
3. Look at Figure 2. Without touching the trigger, identify the plastic tab circled in red in Figure 2. 4. Slowly pull the trigger. The plastic tab encircled in Figure 2 should disappear into the upper trigger section (Figure 3). 5. Slowly release the trigger. The tab should reappear as shown in Figure 2 completely on its own. 6. Repeat steps 4 and 5 several times. If the small tab as shown in Figure 2 reappears each time, your pistol does not require repair. 7. If the small tab does not consistently reappear as shown in Figure 2, YOUR PISTOL MUST BE RETURNED FOR SERVICE. If you are uncomfortable conducting the inspection outlined above, or are unsure whether the condition described in this notice applies to your firearm, please take your firearm to your local M&P Certified Armorer or send your firearm to Smith & Wesson for inspection. M&P Armorers can be found on the Smith & Wesson website under Find a Dealer. If after inspection it is determined that the condition outlined in this safety alert exists, the firearm must be sent to Smith & Wesson for repair. |
| REMEDY/ACTION TO BE TAKEN: | STOP USING YOUR FIREARM UNTIL IT HAS BEEN INSPECTED AND, IF THE CONDITION IS FOUND, REPAIRED.Your firearm must be inspected to determine whether it exhibits the condition identified in this notice. To determine whether your firearm is affected by this condition, please inspect your firearm by following the inspection instructions above.If your firearm is affected by the condition outlined in this notice, please send your pistol to Smith & Wesson. Your firearm will be inspected, and if necessary, repaired at no cost to you. Your firearm will be returned within 5 to 7 business days. All shipping and repair costs will be covered by Smith & Wesson.
Outside the United States, click here for a list of Authorized Warranty Centers that will repair your pistol. |
| CONSUMER CONTACT: | Please contact Smith & Wesson directly at 877-899-6259 to arrange for the repair, if necessary, of your pistol. |
Vortex Introduces Viper HS-T Riflescope
July 9, 2013 |
Vortex Introduces Viper HS-T Riflescope
Middleton, Wis. – Blending many of the best features of Vortex’s incredibly popular Viper HS and Viper PST riflescopes, the new Viper HS-T (Hunting Shooting Tactical) is positioned to be big a hit among hunters, as well as tactical enthusiasts.
Available in 4-16×44 MOA and mrad models, the Viper HS-T boasts an all-new, hashmark-based second-focal-plane reticle, perfect for accurate holds at extended ranges. Mrad reticle hashes subtend in .5 and full-value increments. MOA reticle hashes subtend in 2 MOA increments. Both are set for use at the riflescope’s maximum 16-power magnification.
Incredibly precise, repeatable and durable target-style windage and elevation turrets built specifically for dialing, top off this highly versatile riflescope’s long range performance features. And with Vortex’s CRS (Customizable Rotational Stop) system, shooters can quickly re-index their turret after temporary elevation corrections have been made. The HS-T’s 30mm one-piece machined aluminum tube ensures ample travel for optimal adjustment.
An ultrafriendly eyebox with generous 4 inch eye relief and fast focus eyepiece gets shooters on target with ease. XD (extra-low dispersion) glass guarantees sharp, crisp images from edge to edge. Lenses fully multicoated with Vortex’s proprietary XR coatings offer superior light transmission for optimal performance in critical low light scenarios. Exterior lenses feature ArmorTek, an ultrahard optical coating engineered to protect against scratches, oil and dirt.
O-ring sealed and purged with argon gas for 100 percent waterproof/fogproof performance. Shockproof construction withstands recoil and impact from every angle.
Available: 4-16×44 (VMR-1 MOA Reticle), 4-16×44 (VMR-1 mrad Reticle)
MSRP: $659
American-owned, Wisconsin-based Vortex Optics designs, engineers and distributes a complete line of premium binoculars, riflescopes, spotting scopes, tripods and related accessories. Dedicated to exceptional quality, value and unrivaled customer service, Vortex backs its products with its unconditional, lifetime VIP-warranty. Built on more than 20 years of experience in the optics industry, Vortex is rapidly emerging as a leading brand in the optics market.
Vortex – The Force of Optics | www.vortexoptics.com
Media Contact: Mark Boardman (800) 426-0048 mboardman@vortexoptics.com
– See more at: http://www.thetacticalwire.com/story/292814#sthash.14WL1RVi.dpuf
Steve Hornady Explains Increased Production Plans
Thompson/Center Arms Recalls Certain ICON, VENTURE and DIMENSION Rifles
Thompson/Center Arms™ has identified a condition that may cause the safety lever on certain ICON®, VENTURE™ and DIMENSION® rifles to bind, preventing the safety from becoming fully engaged. In this situation, closing the bolt may move the safety to the fire position. The rifle will not fire unless the trigger is pulled. However, out of an abundance of caution, we are taking this action to recall the rifles so that the firearm can be inspected by our technicians to ensure that the safety lever functions as designed.
This recall applies to all ICON, VENTURE and DIMENSION rifles manufactured by Thompson/Center Arms prior to June 13, 2013.
STOP USING YOUR RIFLE AND RETURN IT TO THOMPSON/CENTER AT ONCE.
Because the safety of our customers is our utmost concern, we ask that you stop using your rifle until we have an opportunity to inspect the safety lever to ensure its proper function.
To facilitate the inspection and repair, if necessary, of your rifle safety lever, please contact Thompson/Center’s customer service department to receive instructions and a pre-paid shipping label for the return of your rifle to Thompson/Center. Thompson/Center will repair the rifle at no cost to you, and return it to you as quickly and efficiently as possible.
Additional information will be available shortly on our website at www.tcarms.com. In the meantime, if you have any questions about this recall, please contact Thompson/Center at (800) 713-0355.
Dealer Contact:
(800) 713-0355 – See more at: http://www.thetacticalwire.com/story/291204#sthash.gJpTeL91.dpuf
Plinker Tactical Introduces Gen III .22 LR magazine for S&W M&P15-22
CORNELIUS, NC – Plinker Tactical, LLC makers of American-made firearms magazines, accessories and components, have released the next generation Plinker Tactical .22LR magazine for the Smith & Wesson®M&P15-22.
The Gen III Plinker Tactical .22LR magazine holds 35 rounds, more than the competition, providing longer firing sessions without reloading. Made in the U.S.A. of the most durable, quality polymers, the Gen III mags are impact and solvent resistant. The magazine has evolved to its most robust form yet capable of punishing target sessions without jamming. Heavy duty construction with no screws or exposed springs keeps debris out and performance in.
Every Plinker Tactical magazine is 100% guaranteed for life against breakage. Available in Black, Flat Dark Earth or Olive Drab with an MSRP of $29.99.
For Plinker Tactical information, visit www.plinkertactical.com. Join the conversation on ourFacebook. For more information on Plinker Arms, visit www.plinkerarms.com.
About Plinker Tactical, LLC:
Headquartered in Cornelius, North Carolina, Plinker Tactical, LLC was founded in 2010 by two firearms enthusiasts with backgrounds in firearms manufacturing, NASCAR® engineering and combat shooting. Plinker Tactical and its parent company, Plinker Arms, LLC manufactures American made firearms magazines, accessories and components. www.plinkertactical.com www.plinkerarms.com
Media Contact:
Laura Burgess Marketing
Laura Burgess
PO Box 13978
New Bern, NC 28561
P: 252-288-5805
laura@lauraburgess.com
Plinker Tactical, LLC
18636 Starcreek Drive, Suite G
Cornelius, NC 28031
P: 1.704.895.6645
www.plinkertactical.com
www.plinkerarms.com
© Copyright 2008-2013 The Tactical Wire. All Rights Reserved.
– See more at: http://www.thetacticalwire.com/story/291475#sthash.5EXJaHBV.dpuf
Product Warning And Recall Notice: Winchester® 5.56mm M855 62 Grain
March 28, 2013 |
Product Warning And Recall Notice: Winchester® 5.56mm M855 62 Grain
|
Olin Corporation, through its Winchester Division, is recalling one (1) lot of its 5.56mm M855 62 Grain PENE centerfire rifle ammunition.
Symbol Number: ZGQ3308
Lot Number: WCC10M106-004
Through extensive evaluation Winchester has determined the above lot of 5.56mm M855 ammunition may contain incorrect propellant. Incorrect propellant in this ammunition may cause firearm damage, rendering the firearm inoperable, and subject the shooter or bystanders to a risk of serious personal injury when fired.
DO NOT USE WINCHESTER® SYMBOL NUMBER ZGQ3308 LOT NUMBER WCC10M106-004 5.56mm M855 62 GRAIN PENE AMMUNITION. The ammunition Symbol Number and Lot Number are ink stamped on the outside of the 900-round shipping container, and on the outside of the 30-round carton as indicated here:
To determine if your ammunition is subject to this notice, review the Symbol Number and Lot Number. If it is Symbol Number ZGQ3308 and Lot Number WCC10M106-004 immediately discontinue use and contact Winchester toll-free at 866-423-5224 for free UPS pick-up of the recalled ammunition. Upon receipt of your recalled ammunition, Winchester will ship replacement ammunition directly to you.
This notice applies only to Symbol Number ZGQ3308 with Lot Number WCC10M106-004. Other Symbol Numbers or Lot Numbers are not subject to this recall.
If you have any questions concerning this 5.56mm M855 ammunition recall please call toll-free 866-423-5224, write to Winchester (600 Powder Mill Road, East Alton, IL 62024 Attn: 5.56mm M855 Recall), or visit our website at www.winchester.com.
We apologize for this inconvenience.
WINCHESTER
Winchester Issues Recall for 5.56 Ammo
Winchester Issues Recall for 5.56 Ammo
| by Daniel Terrill Amid a national ammo shortage this is probably the last thing you want to hear. Winchester has issued a recall for some of their 5.56mm centerfire rifle ammo Feb. 4.
The Winchester 5.56mm M855 62 Grain Pene ammunition has the symbol number “ZGQ3308″ and the lot number “WCC10M106-004″.
The company stated in the recall notice that after an extensive evaluation they found that a single lot of Winchester 5.56mm M855 62 Grain Pene (penetrator) ammunition may contain incorrect propellant, an issue that if used may cause damage to the firearm or render it inoperable, or may cause injury to the shooter or bystanders.
The 5.56mm M855 is an economical brand that features a steel core and a green penetrating tip. Online a box typically costs $10.
The company asks that you do not use the 5.56 ammo from boxes marked with the symbol number “ZGQ3308″ and the lot number “WCC10M106-004″. Both identifying numbers are stamped on the outside of the 900-round shipping container, and on the outside of the 30-round box.
Winchester asks that if you do have a box of defective ammo to immediately discontinue using it and contact the company to exchange it at no cost to the consumer. You can contact Winchester at 866-423-5224 and they’ll arrange for free UPS pick-up. As soon as the company receives the package, a replacement box will be shipped out.
The company can also be reached via snail mail. If you have questions relating to this issue write to Winchester at 600 Powder Mill Road, East Alton, IL 62024 with “Attn: 5.56mm M855 Recall” at the top, or visit the company’s website at www.winchester.com.
Categories: Ammunition, Product & Industry News, Safety
Smith & Wesson® Introduces New M&P® Pro Series C.O.R.E. Pistols
November 8 : 2012
Smith & Wesson® Introduces New M&P® Pro Series C.O.R.E. Pistols
|
SPRINGFIELD, Mass. — Smith & Wesson Corp. today announced that four new models have been added to the Company’s premier line of M&P® polymer pistols. Based on the popular Pro Series line of competition ready firearms, the new M&P C.O.R.E (Competition Optics Ready Equipment) models offer consumers a specialized platform for adding accessory optics to their personal handguns. Engineered to accept six popular styles of competition based optics, the M&P C.O.R.E models are easily adapted to meet any demand.
At the foundation of the new M&P C.O.R.E. resides a specialized mounting platform on the slide of the pistol that can be conveniently changed to match the desired optic. Through the use of removable brackets, consumers are able to simply install the corresponding mounting screws to achieve the precise fit and height required. Designed to work in conjunction with the Trijicon RMR®, C-More STS, Leupold® DeltaPoint™, Docter, Insight® MRDS™ and JPoint™, the M&P C.O.R.E. offers quick and custom sight installation for the industry’s top aftermarket red-dot sight manufacturers.
The new M&P C.O.R.E. models will be available in both 9mm and .40 S&W with either a 4.25 or 5-inch barrel configuration. Engineered as a true competition platform, each model will retain original design features including a polymer frame with a through-hardened stainless steel slide and barrel, ambidextrous operating controls, striker fire action and Melonite® finish. For improved handling the M&P C.O.R.E. models feature a new textured interchangeable back strap with prominent stippling. Three patented palmswell grips are supplied with each pistol, providing shooters the ability to tailor the grip size to their personal preference.
For improved accuracy and precise shot placement during competition, the M&P C.O.R.E. pistols are standard with a Performance Center sear. The specialized sear allows for a crisp 4.5 pound trigger pull along with a faster, defined reset in between shots. On top of the slide, Smith & Wesson has added higher sights that can be used in concordance with the mounted optic. Other standard features of the new pistols include a crowned muzzle for improved accuracy, picatinny-style equipment rail and reversible magazine release.
Internal features of the new M&P C.O.R.E. remain consistent with the original design and include a stainless steel internal chassis designed to reduce flex while also providing a stable shooting platform. The M&P pistol’s low-bore axis helps maintain ease-of-use and a comfortable feel and the passive trigger safety prevents the pistol from firing if dropped regardless of angle. A sear release lever eliminates the need to press the trigger in order to disassemble and the simple take down lever is located on the left side of the frame. A loaded chamber indicator is present on top of the slide and rear scalloped slide serrations enable easy firearm manipulation.
The 9mm M&P C.O.R.E. is standard with a 17+1 round magazine capacity and the .40 S&W variant features a 15+1 round capacity. Without a mounted optic the 5-inch barrel models have an empty weight of 26 ounces while the 4.25-inch pistols measure two ounces lighter.
For more information on the new M&P C.O.R.E models, please visit www.smith-wesson.com
About Smith & Wesson
Smith & Wesson Holding Corporation (NASDAQ Global Select: SWHC) is a U.S.-based leader in firearm manufacturing and design, delivering a broad portfolio of quality firearms, related products and training to the consumer, law enforcement, and military markets. The company’s brands include Smith & Wesson, M&P and Thompson/Center Arms. Smith & Wesson facilities are located in Massachusetts and Maine. For more information on Smith & Wesson, call (800) 331-0852 or log on to www.smith-wesson.com.
Remington Acquires TAPCO
November 6 : 2012
Remington Acquires TAPCO
Madison, NC – Remington Arms Company, LLC (Remington), part of the Freedom Group Family of Companies, announced today it has acquired The American Parts Company Inc. (TAPCO).
TAPCO is a designer and marketer of American-made aftermarket accessories and replacement parts for handguns, rifles, shotguns, modern sporting rifles and other tactical firearms. All aspects of the product development cycle are managed from within the company. State of the art computer aided design, rapid prototyping and extensive testing have allowed TAPCO to bring innovative and dependable products to the shooting marketplace.
“TAPCO has been in business for more than 25 years and has established market strength through its high quality U.S.-made products,” said George Kollitides, Chairman and Chief Executive Officer of Freedom Group. “This acquisition will enhance our positioning in the accessories market and allow us to further our research and development capabilities.”
“With the acquisition of TAPCO, Remington continues to demonstrate its commitment to the firearm parts and accessories business,” said Scott Blackwell, President of Freedom Group. “TAPCO is well-known as a leader in delivering innovative and dependable products to the shooting marketplace. We are excited about the breadth of the products they bring to our portfolio, and we look forward to utilizing our resources to ensure our consumers and OEM partners benefit from this important acquisition. We welcome TAPCO and its employees into our family of companies.”
TAPCO will continue day-to-day operations at its Kennesaw, Georgia, facility.
###
About Remington Arms Company, LLC
Remington Arms Company, LLC, (“Remington”) headquartered in Madison, N.C., designs, produces and sells sporting goods products for the hunting and shooting sports markets, as well as solutions to the military, government and law enforcement markets. Founded in 1816 in upstate New York, the Company is one of the nation’s oldest continuously operating manufacturers. Remington is the only U.S. manufacturer of both firearms and ammunition products and one of the largest domestic producers of shotguns and rifles. The Company distributes its products throughout the U.S. and in over 55 foreign countries. More information about the Company can be found at www.remington.com.
Media Contact:
Jessica Kallam Jessica.kallam@remington.com (800) 243-9700 ext. 8578
Jessica Kallam Jessica.kallam@remington.com (800) 243-9700 ext. 8578